Howbi Posted January 3, 2016 Share Posted January 3, 2016 As compiled and posted by Magfan.....for quick reference on the LD thread posters....HB. Lets bring back the list of commands...All these can be used when programming what Loco went over a sensor.All these commands can be programmed in any or every sensor. Loco Detection Commands -On signal greenOn signal redFor Locos;For train type(s)For forward directionFor reverse directionFor any directionStop locoStop loco on signalResume loco on signalReduce loco speed toIncrease loco speed toSet to cruise speedSwitch right pointSwitch left pointSet clear signalSet danger signalActivate loco functionPlay sound fileRun program file So you can set speeds, set signals, set points, play tunes, etc and as fishy stated, Run a program. Link to comment Share on other sites More sharing options...
PJ_model_trains Posted January 3, 2016 Share Posted January 3, 2016 These are missing commands for LD which are needed for it to work effectively On signal yellowOn signal yellow-yellowPLUSSet signal yellow (Extra Caution)Set signal yellow-yellow (Caution) Yellow and Yellow-Yellow aspects are allowed in our signals in RM, they are also programmable in program routes They are essential for LD at present the following only are included: On signal greenOn signal redPLUSSet clear signalSet danger signal Link to comment Share on other sites More sharing options...
Fishmanoz Posted January 3, 2016 Share Posted January 3, 2016 If my memory serves me correctly, this is the list as first appeared around v1.56 as compiled by PJ. Has anyone checked since then? Link to comment Share on other sites More sharing options...
Howbi Posted January 3, 2016 Author Share Posted January 3, 2016 @magfan..............my apologies to you for incorrectly accrediting that list to you and apologies to PJ for not giving him the credit for posting it.............slapped wrist & pay attention in future HB. Link to comment Share on other sites More sharing options...
hosh Posted January 3, 2016 Share Posted January 3, 2016 On signal green - ok, this is pretty straight forward. Toot horn, flash lghts, set speed, etc. On signal red - so there will be an option other than stopping? Stop loco on signal - on a signal other than red? Or does this mean a signal from any device, not necessarily a signal. A signal (instruction) from another sensor perhaps? Resume loco on signal - on a signal other than green? And same as for :Stop loco on signal". I'm hoping the Stop and Resume on signal commands imply red and green. So unless instructed otherwise for given trains, at a given sensor you simply tell it to Stop loco on signal, Resume loco on signal and it simply does this for all trains. Link to comment Share on other sites More sharing options...
PJ_model_trains Posted January 3, 2016 Share Posted January 3, 2016 CREDITS - they go to HRMS not me, OK I prepared the list to help members in the first place but, ah ho When HB created the New Thread with the commands list I though what a good idea, lets keep it for those items. The missing items made sense to add but them.............. Apologies I guess to hosh, same questions he just got wrong thread! No further comments from me on here! Link to comment Share on other sites More sharing options...
PJ_model_trains Posted January 3, 2016 Share Posted January 3, 2016 If my memory serves me correctly, this is the list as first appeared around v1.56 as compiled by PJ. Has anyone checked since then? I will check tomorrow, just got PC set up today, temporary in wrong room and just adding Norton. I will check the LD commands in RM tomorrow ;o) Last comment on here, other than an update to follow!!! Link to comment Share on other sites More sharing options...
Fishmanoz Posted January 3, 2016 Share Posted January 3, 2016 Agree, no more comments, only updates on command list. Adam, suggest you lock and sticky this thread please. Only to be updated when someone emails you with any additional instructions to be added to the first post. Or maybe wait for PJ's confirmation, then do it. Link to comment Share on other sites More sharing options...
hosh Posted January 4, 2016 Share Posted January 4, 2016 Ok, so this is just for reference - I have a txt file on the desktop for that anyway. Link to comment Share on other sites More sharing options...
PJ_model_trains Posted January 4, 2016 Share Posted January 4, 2016 Below are the LD commands in RM - 4-1-2016 On signal yellowOn signal double yellowOn signal flashing yellowOn signal flashing doubleOn signal flashing greenOn signal greenOn signal redFor Loco(s):For train type(s):For forward directionFor reverse directionFor any directionStop locoStop loco on signalResume loco on signalReduce loco speed toIncrease loco speed toSet to cruise speedSwitch right pointSwitch left pointSet clear signalSet danger signalActivate loco functionPlay sound fileRun program file We ask HRMS to consider the following commands please Set Yellow signalSet Double Yellow signal HRMS you may also wish to consider the setting of the other flashing aspects in this set.Setting signal aspects to control speed of loco's to signal variations is going to be a very important part of automating the running of our trains. Above we can see the additional LD commands for signals. It is clear HRMS are totally commited to the advancement of the software and making LD a market leader in model railway control. It is also very clear, and we should be encouraged, that they are continuing to listen to our comments and requests. From all members of the forum 'Thank you and Happy New Year'. Link to comment Share on other sites More sharing options...
PJ_model_trains Posted January 4, 2016 Share Posted January 4, 2016 I will send a message to Adam to remove all messages other than the new updated list of commands and lock this thread keeping it just for reference. Please do not add any further comments to this thread. Hopefully Adam will remove all posts except the main list of commands added today and lock this thread, only to be added to by contacting an administrator. We can all use it as a forum reference tool and refer members back to it instead of having to keep cutting and pasting lists in other threads. Link to comment Share on other sites More sharing options...
Fishmanoz Posted January 4, 2016 Share Posted January 4, 2016 Well done PJ. Agree with request to Adam. Lots of other instructions needed too, starting with those relating to x,y coordinates. But little birdie says not now. Link to comment Share on other sites More sharing options...
Recommended Posts