Kim-344602 Posted October 6, 2023 Share Posted October 6, 2023 Just got a couple of new TXS decoder and trying to link/set them up.Have gone into the app and searched. It finds the device but not as "ready to link". Comes up under resettable devices. However. I don't have the code to do it as this is usually emailed after you have linked and set up the device. Any suggestions? Link to comment Share on other sites More sharing options...
Kim-344602 Posted October 6, 2023 Author Share Posted October 6, 2023 Please ignore the above question. Found the answer.I exited the app with the decoder powered up and scanned again. This time it worked. Not sure if it's the correct answer but seems that you need to start the app after powering up the device rather than the other way round. Link to comment Share on other sites More sharing options...
SteveM6 Posted October 6, 2023 Share Posted October 6, 2023 You have found the Hornby recommended solution by accident but for any others in the same boat, its one of the many tips contained in the troubleshooting guides and pinned posts at the top of the forum.I can't recommend them enough.🙂 Link to comment Share on other sites More sharing options...
Nigel-369429 Posted October 10, 2023 Share Posted October 10, 2023 Thanks for help...have discovered that one must log out of app then power chip before loging in again! Then it all worked. Very impressed!! Link to comment Share on other sites More sharing options...
Nigel-369429 Posted October 20, 2023 Share Posted October 20, 2023 ...and if that doesnt work restart the phone!!! Solved it for me! Link to comment Share on other sites More sharing options...
ColinB Posted October 28, 2023 Share Posted October 28, 2023 So where in the menu structure is the rescan key option? I only managed to get it to do it by removing the app and reloading it. The app on my phone had got completely corrupted. Link to comment Share on other sites More sharing options...
SteveM6 Posted October 28, 2023 Share Posted October 28, 2023 Settings > Link device > Start Scan Link to comment Share on other sites More sharing options...
ColinB Posted October 28, 2023 Share Posted October 28, 2023 Ok, thanks for that. So I have a loco loaded and I am controlling it with Bluetooth. Now if I do a scan I should see my device that I am controlling appear in the scan, but it doesn't. Is it meant to do that. Link to comment Share on other sites More sharing options...
SteveM6 Posted October 28, 2023 Share Posted October 28, 2023 No, you scan it initially as part of the linking process. Once linked it will appear in the ‘Engine Shed’ and at the top of the control/operating screen. From there you can add a photo, rename, renumber etc. Link to comment Share on other sites More sharing options...
ColinB Posted October 28, 2023 Share Posted October 28, 2023 In my case I wanted to see if the device had got damaged because its properties had got corrupted. It doesn't matter I found a way to sort it out. Thanks for the info. Interestingly once I deleted the app and rescanned it sorted the device out. My device initially appeared on the app but I couldn't change from Bluetooth to DCC. Link to comment Share on other sites More sharing options...
96RAF Posted October 29, 2023 Share Posted October 29, 2023 From Settings you can get to this page from Manage Devices and pick the decoder or from Engine Shed you pick the loco, then Manage. The green block items tell you decoder health. Link to comment Share on other sites More sharing options...
ColinB Posted October 29, 2023 Share Posted October 29, 2023 Yes 96RAF thanks for the information. Interestingly in my case in my case I just got the opinion that the app was pointing to the wrong decoder or had somehow screwed itself up because it had disabled DCC and Bluetooth controls but supposed could still see the decoder. Deleting the App reloading it and starting from scratch fixed it, well the non sound part of the decoder. After setting the least significant bit in CV29 the sound still doesn't work, more importantly how did it get cleared, I don't touch CVs. I suspect something on the sound circuit has blown, I am waiting for a response from Hornby. I also had issues reading CVs on my Elite, sometimes it worked sometimes not, more interestingly when it didn't work I got a buzz on the speaker. Anyway it can go back to Hornby, if I had done something dubious I would own up but in this case all I did was fit the decoder and PowerBank properly into the tender so I could get the body on and it stopped working. Link to comment Share on other sites More sharing options...
SteveM6 Posted October 29, 2023 Share Posted October 29, 2023 I am confused by your reference to CV29 - as far as I am aware, there is nothing on there that relates to sound. Link to comment Share on other sites More sharing options...
ColinB Posted October 29, 2023 Share Posted October 29, 2023 I know the the person who posted it highlighted their error several posts later. The bit in question is the direction bit. I have done everything I can think of but the sound does not function so it is a return job. As to the weird effects I was getting with the decoder and app who knows. There does seem to be an issue accessing CVs on DCC occasionally, normally I would blame the track but I double checked that. The decoder now works perfectly on DC and Bluetooth without sound, I even ran it around the layout for an hour without it failing. So obviously something has gone wrong with the output stage of the sound. Link to comment Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now