KNAP

Latest Sept 21 used. Hoping for an update! Rails added address for me. However, I also have a 2nd Manor that had same issue and I have to use on 03. HMRS was contacted. Next problem Hornby 9F Blue tooth loaded on tablet, but stop is a dead stop, no deceleration even when set a 255. elink will only work with address 03, but decelerates when stopping.

Tried all the suggested methods

Short address did not work, but have received this message

Accurascale have confirmed no lock. Now this is the important bit. Do NOT try to read any CV values using the Green tick. Does it matter if CVs have previously been read?

Anyone having a problem changing ID for Accurascale DCC Sound Manor? Have tried the methods suggested above without any luck

How many locos have been programmed, as there is a limit before you have to use groups.

I did a few posts back.

Problem has been fixed, by deleting yhe corrupt loco settings.

The loco is set up on CV 159 and runs fine at low speeds.although now 6 and 10. The CV 160 is just a test to see if I could recreate what happened (also offline - not connected to elink) With the higher shunt rather than cruise speed RM created the value in speed factor box. the voice controll entry and loco detection ID.value of 160 The green box 150mph was just a previous test at using the speed factor boxes.

As suggested by william david, I deleted the orignal set up and set the loco up again and all works as normal. I've not used the stopwatch facility but on checking it requires both a time range and max speed range. . ..However, at first I set the shunting speed higher than cruise speed and had to correct after saving. I have recreated this and there does appear to be a vulue written to max spped and also a "F" written to voice control /media/tinymce_upload/4fef055d07764bfb6dbbfba6edef2b8d.png

Originally I had them set at 30 and 50 mph but the loco speed was too fast. I then set them lower and it was after that I noticed the speed column just went to maximum on pressing either Shunt or cruise. I also tried lowering speed using CV s with no joy.

The screenshot is a png and 472KB. Maybe after hours on Friday so will wait to Monday. Shunt speed is 3 and Cruise 6 mph.

How do you post ascreenshot asI have been trying the upload image button without success.

/media/tinymce_upload/53930b23bfccdebd235b67fe1bdb1c44.png Hopefully can see from above cruise for 5MT compared to cruise for DP1 9new loco) which is set at 6mph. Set low as at 40mph the loco was flying before I noticed the speed column at max. I should be on latest version from above.

Railmaster e link set up and other locos working as they should. New Diesel and Zimo DCC Sound with shunting and cruise speed set. On applying either shunting and cruise the speed controller column goes to maximum and the loco accelerates up to maximum spped rather than shunting or cruise. I have tried re programming loco with no difference. Appears to be a railmaster bug but do not know how to solve problem.

How do you go back to 1.69?

As a elink and windows 10 user. Bypassed Anti Virus No handshake errror and loaded, However nothing worked so no comminication AC = 1 Loaded and worked until a constant loss of controller error message. Started a loco but could not stop it.

Only relates to elite controllers, rather than elink with Windows 10?

I have reported issue as an elink user.. However, last time, with the loco restriction, they could not gain remote access.

Tried suggestions without much success. The unplug USB worked once but most be random as would not work again.

Updated today and had a handshake communication problem. Not sure from reading this threead that there is an easy solution.

A method of ballasting I am trying, is to use double sided sticky tape (1 side only under track sticky side up and ballast shoulder using both sides ). This method would allow lightweight ballast to be used without floating problems. My access, rather than lifting, uses door hinges for a 4 ft opening and just needs locating points for alignment. Runs a 4 track main line over this section so a reliable set up.