William1707821657

Hi all , I have a relatively basic question regarding armored vehicles with seperatley molded suspension parts , this goes mainly for 1-35 I found on my current build that the suspension arms are seperate and when glued in they have a lot of wiggle and a fair bit of play , this makes it tough for me to make sure the tank is sitting level and not leaning , so i was just curious how the pros do it thinking_face regards William

Hi all , hope you are doing well , I recently purchased this kit and found the fit to be very good aside from what minor annoyance , the one piece canopy has a minor fit issue and doesn't fit very flush with the fuselage causing a minor gap where the parts should connect , has anybody else had this issue? Regards Will

sure! A55307

Hi all , I was just looking for some advice , I recently started on my sea king kit and noticed it had some really nasty fit issues , like the main floor being warped , another issue I had was with the windows . When the side parts where put in , I would put the top part on and the sides would be pushed out , all in all I haven’t had much luck with this kit , can anybody give me any advice , I would love to hear your opinion of this kit. regards William

You are amazing Ratch thanks!

Yes the paint is spray is the Vallejo model air range of paints and the stynlrez and Vallejo primer seems to be happening with the primer more so than the paint , however I can’t confirm that

Hey guys , just got into airbrushing a F-4 phantom kit with a H&S evolution with a .4mm nozzle and needle , and a pressure of usually 1.5 to 2 bar , my main issue is when I shine a torch on my model at an angle , I always see the finish looks rough or coarse I use Stynlrez primer which has arround 3 drops thinner and mixed well , and sprayed on the kit until the paint looks wet , the funny thing is I am baffled by whats causing this , as my first time i remembering it happen was with my first airbrush (chinese no brand) and a different compressor , which both my airbrush and compressor have changed since then and i still get the affect , i spray close but not too close , maybe 3 inches or so away from the piece and vary my motions by maybe moving in circles or going up and down , but mostly just left and right , its been a year now and i still dont know whats causing it , but i really want to solve this once and for all.

Okay firstly I'm not using "Bad" brushes , I'm using royal and langnickel synthetics , the paint is yellow , which if Im correct has a much finer ground pigment, I thin because on the humbrol YouTube channel they show a step by step guide on how to make your first airfix kit they advice thinning your paint for a smoother finish , I have been on other forums and they say Vallejo is very thick and requires thinning so that's why I use vallejos Thinner medium , when painting large areas with my WIDE brush I prefer their thinner as I find the paint keeps its strength whereas with TAP water it's a little weaker , I have spoken to other Modellers and have agreed that yellows are weaker as their pigment is more finely ground , i Left the paint for a drying time of 30 minutes as that's what I found on google if that's not right then shame on vallejo for not putting the drying time on the bottle

i honestly dont know on how somebody can brushpaint a large area with with vallejo paint and no thinner! it must have strokes everywhere as vallejo model colour is such a thick paint , i find this forum so confusing sometimes and at times i dont know what to listen to

I use wide brushes on larger areas , and im friends with owen , i simply hate brushpainting , its generally making me want to just give up , i always find a one imperfection and just chuck the model in the bin

I Have! like the first time you told me to , i have tried 3 times! humbrol , revell now vallejo , I dont see how you can simply paint a large surface without thinning! all the tutorials say to thin the paint for better coverage and to eliminate undesirable brush strokes!

Model colour is way too thick to be brushed , I assume you think im using model air?

Hello all , I recentley picked up some vallejo model colour "Desert yellow" which i then brushpainted onto my Tiger tanks exhaust shield , the paint was mixed 50/50 with their thinner , i left it to dry i repeated this another 2 times until i was happy with the finish , once i then went to glue it onto the rear of my tiger , i noticed that the paint didnt feel quite right , baring in mind how hot it is and it could just possibly be sweat , but it felt soft and a little tacky when i pulled my finger off , i cant remember if i have talked about this before however this only happens with lighter tones like yellows and whites etc Many thanks Will

wait it must be humidity right? it was like 23 degrees when i applied it