Rustyjt Posted August 17 Share Posted August 17 Any suggestions on the hight above carriage roof a platform canopy should be? Looking at photographs they seem quite consistently close to a carriage but could be from perspective of viewing from below. Just trying out some options and feel I need to lower the ones shown in attached photo if I stay with them. Link to comment Share on other sites More sharing options...
moawkwrd Posted August 17 Share Posted August 17 (edited) They don't look a million miles away from the prototype - it might just be that style that makes them look overscale. The flat sided ones had a considerable gap between the top of the carriage as you can see here: https://www.warwickshirerailways.com/gwr/gwrls226.htm https://www.warwickshirerailways.com/gwr/gwrls2149.htm Maybe dropping the supports by 2-3mm would be enough? Edited August 17 by moawkwrd 1 Link to comment Share on other sites More sharing options...
Rustyjt Posted August 17 Author Share Posted August 17 Tend to agree with you, variations wherever I look. To my eye they just felt a bit high. Must be a spec for gauging but that obviously would just be the minimum. Will try one reduced a couple of mm and see how it looks. Link to comment Share on other sites More sharing options...
StuLarge Posted August 17 Share Posted August 17 Lots of info on RM web historically they also overhang the platform edge by about 1ft and height was above the loading gauge. Modern guidance is clear height of 4m minimum (so 33.3mm) 1 Link to comment Share on other sites More sharing options...
Stephen-1260829 Posted August 17 Share Posted August 17 @Rustyjt I have the same platform canopies as you, I think. Although not a scientific comparison, I have taken a few photographs for you to see to compare against figures. The figures are the ModelU TT120 station staff set (Not 1:100th scale) The canopy lines up reasonably well with the roof line of the PECO Station building. Hope this helps 🙂 3 Link to comment Share on other sites More sharing options...
Stephen-1260829 Posted August 17 Share Posted August 17 (edited) I think that the issue with the canopies is that they are a little too "chunky" in terms of the wooden valance. They just look so oversize (in my opinion) in some of the images, it could look like each valance board has a scale size of 40 cm wide. I think they would be around 14 -16 cm wide Edited August 17 by Stephen-1260829 added the letter K to loo 1 Link to comment Share on other sites More sharing options...
Mac202 Posted August 17 Share Posted August 17 I understand that the canopies came down quite low so as to avoid smoke and steam emitted from the engine becoming trapped under the canopy and choking the passengers. 2 Link to comment Share on other sites More sharing options...
Stephen-1260829 Posted August 17 Share Posted August 17 Just now, Mac202 said: I understand that the canopies came down quite low so as to avoid smoke and steam emitted from the engine becoming trapped under the canopy and choking the passengers. @Mac202 That would make a lot of sense!!! Link to comment Share on other sites More sharing options...
Rustyjt Posted August 17 Author Share Posted August 17 As usual, great comments and help. Thanks all. 1 Link to comment Share on other sites More sharing options...
Rallymatt Posted August 17 Share Posted August 17 Compared to a scale figure, the downward slats are the same width as an adult human. I can only recall seeing the slats about 15-20cm wide on the real thing. A disparity in the scale there will upset the overall appearance. Perhaps cut them down the centre with a fine saw blade, the gap between could help change the overall look. 1 Link to comment Share on other sites More sharing options...
StuLarge Posted August 18 Share Posted August 18 (edited) Bear in mind different model makers take a different approach to achieving the desired Impression and there is a consideration for the materials they are working with. Counting bricks against door heights is my rivet counter moment: IRL Brick (metric) gauge = 75mm Hornby terrace house = 140mm resin Greenwood Lazer = 123mm plywood Auhagen signal box = 77mm injection mould plastic All different materials all different dimensions required to give the impression of brickwork. Some sage words from YorkModelRail.com who offer some fine pieces for scratch building including canopy valences: "It’s important to get roofs to look good, as it’s the most prominent feature when you look down onto the model layout" Edited August 18 by StuLarge Typo and material info 2 Link to comment Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now