Mark-1276278 Posted September 21 Share Posted September 21 Any idea of the number of sleepers between the elevated piers on this old layout plan? Link to comment Share on other sites More sharing options...
ModelerXYZ Posted September 21 Share Posted September 21 Hi Mark. Welcome to the forum. Can you post a picture of the said plan? It would really help to know which plan you are talking about. XYZ Link to comment Share on other sites More sharing options...
JJ73 Posted September 21 Share Posted September 21 Can't be from the Track Plans Edition 14 - cos I've just had a look!!! ๐ค๐๐ Link to comment Share on other sites More sharing options...
JJ73 Posted September 21 Share Posted September 21 But in saying that, depending on how high you are going - say for any of the Bridges - i.e. Grand Suspension Bridge, Viaduct, Girder Bridge etc etc - then you will need the R658 Inclined Piers - which is a set 7 Piers in different hights to clip on underside of the track!!! You will need 2 sets of theses - 1 set both sides of the bridge I would imagine, or you could get the R 909 Elevated Track Support Set - you just need 1 set of these as it come with supports for both sides!!! Or if it just High Level Piers you Need then it is R659 a pack of 3 - Hope that this helps in some way!!! ๐ค๐ Link to comment Share on other sites More sharing options...
What About The Bee Posted September 22 Share Posted September 22 I could not find any reference to Hornby Track Plan E5.ย Hornby Track Plan 5E does exist however.ย I think this the plan @Mark-1276278is referring to. Track Plan 5E 6 ร 4 layout.ย Purple denotes the elevated section.ย This will include 1st radius curves.ย ย The inclined planes will be very steep indeed. As to the "number of sleepers" in the elevated section?ย I'm not certain what you are after.ย Sleepers in each piece of set track could be counted.ย Would you kindly clarify what you are trying to achieve Mark? Thanks Bee Link to comment Share on other sites More sharing options...
Aussie Fred Posted September 22 Share Posted September 22 (edited) Theย Hornby R 658 Inclined Piersย specify 24 sleepers between each pier or 30 if you want a lower incline. For the high level piers (Hornby R 659 High Level Piers) I have mine at 20 sleepers on the curve and a couple of 15 sleepers where they run over the tramline and roadway. Edited September 22 by Aussie Fred to make more sense Link to comment Share on other sites More sharing options...
Mark-1276278 Posted September 22 Author Share Posted September 22 I have the two sets on incline piers, but Iโm not sure how far to space them out. It is a steep incline, but from memory the only loco of mine which struggled was the Mainline Peak. Not sure how some of the more recent additions to the stable will cope. I might have to resort to magnets. this will be my first layout in 40 years! Link to comment Share on other sites More sharing options...
Rog RJ Posted September 22 Share Posted September 22 (edited) The inclined piers are from the Triang days when locos had magnadhesion and the track was more solid and had a greater rail height (steel & code 150?) making it much stronger.ย Today's track is much flimsier and doesn't work so well with the inclined piers. I would give them a miss and use something better able to support an incline firmly and at a gentler slope to allow modern engines to get up the slope. Edited September 22 by Rog RJ Link to comment Share on other sites More sharing options...
Going Spare Posted September 22 Share Posted September 22 And for the last 30 years or so, the rails have been made of nickel silver which is not magnetic. Link to comment Share on other sites More sharing options...
Mark-1276278 Posted September 22 Author Share Posted September 22 ย below is the plan E5, and a shot of the piers and the track Link to comment Share on other sites More sharing options...
What About The Bee Posted September 22 Share Posted September 22 (edited) Hi Mark R604 and R605 are 1st radius curves (371 mm).ย They are on the track plan you presented. Almost all modern locomotives and rolling stock are designed to 2nd radius curves (438 mm).ย Small 0-4-0 locomotives and short wheelbase rolling stock excepted, they will make the curve. Modern locomotives will likely not make it around that bend, either stalling because the wheels are binding against the track, OR derailing because the wheels do not fit.ย 40 year old locomotives handled 1st radius, today, not so much. Even if they do, that's a lot of strain. Bee Edited September 22 by What About The Bee Link to comment Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now