96RAF Posted November 19, 2023 Share Posted November 19, 2023 96RAF, have you not noticed that you have quote replied to a 3 & 3/4 year old post resurrected by Ian. I am always being tripped up by these old posts. We have tried to get an auto-age lock on them but to no avail and trawling for and manually locking old posts is a no-no job. Link to comment Share on other sites More sharing options...
ColinB Posted November 19, 2023 Share Posted November 19, 2023 It was a good reminder to add "stay alive" to all my 0-6-0 locos, now I have found it can work properly. Link to comment Share on other sites More sharing options...
Brew Man Posted November 19, 2023 Share Posted November 19, 2023 I'm sure there are situations where resurrecting old threads is OK, except for example where a response is being asked of a poster from the original thread who hasn't been heard from since. Link to comment Share on other sites More sharing options...
Barry-350851 Posted November 20, 2023 Share Posted November 20, 2023 Even though it is an old topic, there is some useful info within. I think Mr Lambert's contribution was under appreciated, I used his website for reference quite a bit early on. Make sure it isn't a short cutting the power rather than a stall.Identifying the actual problem makes solving it potentially much easier. To that end, even a simple, cheap, auto-ranging multimeter is a very useful tool. An audible continuity tester is an essential function on one.With the track power off, having a prod around with a multimeter can be quite revealing. If you hold one lead against a known working bit of rail and move the other over the point and all of the rails that should be live you will identify a dead-spot if there is one. It can happen if the contact between the switch rail and the stock rail becomes dirty for example.On the Hornby and Peco points choice, I will say that Hornby points have a bigger dead spot at the "frog" which is better for older stock with course wheels that can short across the frog on the Peco points. This is more of a problem if you use point clips or feed power from all three ends of the point. The both have their pros and cons. Link to comment Share on other sites More sharing options...
Fishmanoz Posted November 20, 2023 Share Posted November 20, 2023 Good summary Barry, and no undervaluing of Brian Lambert (Flashbang) here, one of my most used sources (confirmed in General forum stickies).But one piece of advice missing - ensure your points are dead flat using a straight edge. Pinning in the middle most often is the solution, or filing the tops of frogs if sitting proud. Link to comment Share on other sites More sharing options...
ntpntpntp Posted November 21, 2023 Share Posted November 21, 2023 ... course wheels that can short across the frog on the Peco points. This is more of a problem if you use point clips or feed power from all three ends of the point. The both have their pros and cons. This is why I would always advise against "back-feeding" power into the frog end of any point - even dead frog types. I've seen similar issues with wheels bridging and shorting at the frog in other scales (N and G for example). I treat all points the same as Peco Electrofrog: power only ever fed in from the toe end (blades end) of a formation of points, and isolating joiners on any frog V rails which have a power feed further along. Link to comment Share on other sites More sharing options...
Robert -348404 Posted December 18, 2023 Share Posted December 18, 2023 ive fitted stay alives to all my 060 locos all the rest with tenders I’ve fitted pickups in the tenders if they didn’t have them as made that includes my old triang ones Link to comment Share on other sites More sharing options...
P-Henny Posted December 18, 2023 Share Posted December 18, 2023 Note to readers. This is a resurrected 3&3/4 year old thread. Link to comment Share on other sites More sharing options...
ColinB Posted December 18, 2023 Share Posted December 18, 2023 The thing I have noticed is the difference in "stay alives" and the relationship with the decoder. I found using the same LaisDCC "stay alive" on a Zimo and a Train O Matic decoder on the same 0-6-0 loco, the loco ran longer on the Zimo decoder. I must admit I was surprised Link to comment Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now